Well you could try and buy some TEST. You might fuck it up and grow titts.

Thanks to a few members who take this seriously and want to help others, I was able to find the information I needed. I will be keeping everyone posted on the out come of the “Research.” Thanks again

THE SAME CAN BE DONE WITH FINAPLIX-H TO MAKE TRENBOLONE BASE

Ok guys, this is a simple and easy way to convert Synovex-H to get test base, which can be used in a transdermal application. You will yield anywhere from 12-20g test base from this, depending upon how careful you are with this process. This was developed by Chemo and I got much help from Wardog and Bobo. There are kits out there to do this for test prop inject, but if you want a transdermal or just TNE for whatever reason this is the way to go.

Materials needed:

1. 1 box Synovex-H 2. 2 bottles Heet (available everywhere for your car), around $2-3 3. 1 Bottle Red Devil Lye (Available at grocery stores, Walmart, Hardware store), around $5 4. Glass coffee pot and bucket(s) or other containers 5. Dust masks and/or coffee filters 6. Pill crusher if desired (available at any drug store), around $5

Ok, the how and why(s) of it:

Synovex H is a cattle implant that contains testosterone propionate and estradiol. We are going to remove the estradiol and strip away the propionate ester to end with test base! Ok, on to the conversion:

1. Crush all the syno pellets and place them in the glass coffee pot or bucket and fill with the 2 bottles of Heet. I used a cheap pill crusher I found at a local drug store, made it real quick and easy. If you don’t crush them,they simply take much longer to dissolve. Let the pellets dissolve until the only thing left is the white filler which should settle to the bottom. It wll look like a hit cloudy substance when stirred, no granular particles. With crushed pellets this could be only a few hours.

2. Next filter out the filler materials from the Heet solution. I suggest you get a small funnel like used for adding oil to your car, and place a dust mask in it and filter away. Set that aside and move on to playing with lye, chemical burns are fun! I’m kidding, but be careful you big idiot!

3. Next you need to add saturated sodium hydroxide (Red Devil Lye). This will remove the esters and make the estradiol water soluble. To get saturated sodium hydroxide you need to get a small, thick glass container and do this step in a cold water bath. Start by putting about 2 ounces (or 1/4 cup) of water in the glass, and slowly add the lye a tablespoon or so at a time. IT WILL GET VERY HOT, hence the cold water bath. You will notice the lye dissolve in the water quickly, just keep slowly adding lye until it doesn’t dissolve anymore (remains powder or crystals), then add just a little more water. This is “saturated” sodium hydroxide. Add this to the Heet mix, stir it up, and let it sit for at least a day.

4. Next we will add water to make the test base precipitate out into powder or crystals. There are 2 ways of doing this: A. Add about a 1/2 gallon of water to the mix, stir it up and the test powder will form. If you do this your filtering will be much more time consuming, but it does work fine.

B. “The Wardog Way” This is the more efficient way of getting test base, especially time-wise. Get a paper or plastic sup or container, something that will hold 1/2 gallon or you’ll have to keep filling it up. I used a milk jug. Your mix should be in the coffee pot, so it probably won’t hold a 1/2 gallon of water, so pour it in a bucket. Get some cardboard and cut a hole in it in the center, and place over the bucket. You are going to poke a tiny little hole (with a needle, I mean tiny damnit!) in the bottom of the plastic jug or cup and let the 1/2 gallon of water slowly drip into the heet and lye mix. This will form test crystals, big nice pretty crystals that are easy to filter!

5. Once the water has been added and test powder or crystals formed, now just filter out and rinse the test. I tried using a dust mask for the powder, won’t work, too damn slow. A coffee filter will do fine, or if you have crystals a permanent coffee filter (usually has a reinforced mesh, available at Walmart or grocery store) is better. With test powder expect some time invested in filtering it, with crystals it’s done in minutes. Once you are done, rinse the test repeatedly to make sure the excess hydroxide is off completely, no reason to cycle Red Devil! Now let it dry overnight or give it a bake in the oven at a VERY LOW temp. My oven goes as low as 170, I used that and let it bake to speed up the drying process, but don’t burn it you fool! Now chop it up with a razor like Scarface and there you have test base

The proper solvents to use for tren pellets and powders are Benzyl Alcohol and Benzyl Benzoate both USP Grade.

Combo here for pellets: 4 gram kit use 2 mls BA and 5 mls BB or .5 mls BA and ~1.25 mls BB per gram

Combo here for powders: For powders use .25mls BA and .75 mls BB per gm of pure powder

This is for the conventional kitchen chemist and although not the exact ratios of the variuos magic secret solving solutions they all are just BA and or BB/BB combo

Have you all gotten good results from this, I am interested in giving it a try.

Like many threads you read on this topic, Synovex is not a beginner conversion. It is more time involved and requires an absolute attention to detail. It also has greater potential of messing you up if done incorrectly, given the additional chemicals used.

I am basing my statement on what is required of you if you convert powder or Fina tabs.

My best advice is starting small, only making 5 grams of powder during your first batch. Make sure to use an estrogen stabilizer. Rinse final crystals with distilled water, VERY WELL! Stock up on your On Cycle Therapy and PCT (Post Cycle Therapy); the remaining estrogen, if enough remains, could cause some major Gyno symptoms in some (what am I saying, most).

Hope this helps

Great, thanks for the info..